Search found 70 matches
- Mon Aug 07, 2023 11:20 am
- Forum: Electrical and Electronics Forum
- Topic: Changing Raymarine E80 to Garmin
- Replies: 7
- Views: 863
Re: Changing Raymarine E80 to Garmin
Hello I wrote previously about the change to Garmin but will offer a few things that may be helpful. First I whole heartedly endorse the change from the pathetic C80 to Garmin. I chose the GPSMAP 1243xsv which will fit into the existing C350 Nav Pod. Note the 1242 will not. This was the best improve...
- Sun Feb 19, 2023 12:57 pm
- Forum: Engine / Transmission Forum
- Topic: Diesel Exhaust Hose R&R
- Replies: 5
- Views: 742
Re: Diesel Exhaust Hose R&R
A tough job indeed but you can do it. The responses are excellent. I high endorse the use of heat to remove the old hose, resist cutting. I use a hair dryer on high which takes a little longer. The loop is critical so get that right. I would only add to never reuse the hose clamps and buy the best s...
- Tue Oct 04, 2022 5:35 pm
- Forum: Electrical and Electronics Forum
- Topic: VHF antenna replacement
- Replies: 12
- Views: 2180
Re: VHF antenna replacement
I totally agree with Steve regarding using only the RG8X coax such as Ancor Marine Grade Coax Cable ANC 151550 and quality Shakespeare connectors. Im a big fan of AIS and mentioned the one I installed previously but I did add the Em-Trak AIS external antenna. This I mounted on top of the aft cabin c...
- Sun Oct 02, 2022 5:57 pm
- Forum: Electrical and Electronics Forum
- Topic: VHF antenna replacement
- Replies: 12
- Views: 2180
Re: VHF antenna replacement
I recommend scraping the old Mertz and going with new Shakespeare 5215 antenna. This will fit into the existing bracket. I ran new coax and all new connectors. Even with a split at the bottom of the mast and again at the nav station to add a Em-Trak B923 AIS, we still have excellent VHF reception. A...
- Fri Sep 02, 2022 3:21 pm
- Forum: Rigging Forum
- Topic: Maxwell 800 chainwheel 108 - chain type
- Replies: 5
- Views: 988
Re: Maxwell 800 chainwheel 108 - chain type REVISION
My apologies ... in the last post I captioned 5/16 high test chain as G63. No such thing, it's G43 chain that fits the 108 chainwheel nicely.
- Wed Aug 31, 2022 11:55 am
- Forum: Rigging Forum
- Topic: Maxwell 800 chainwheel 108 - chain type
- Replies: 5
- Views: 988
Maxwell 800 chainwheel 108 - chain type
Like many of you we have a Maxwell VW 800. Ours has the 108 Chainwheel (108 is stamped on the lower half facing upward, cant miss it) I have been everywhere trying to get a correct answer on the correct chain for the 108 wheel. Finally on the phone with Vetus Maxwell 1-410-712-0740 I got a guy willi...
- Sun Aug 28, 2022 11:13 pm
- Forum: Hull, Prop, and Rudder Forum
- Topic: Is aft hull too thick for inside hull transducer?
- Replies: 1
- Views: 517
Re: Is aft hull too thick for inside hull transducer?
Short answer no. I researched this too. Spoke to Garmen, spoke to the best marine electric / electronics firms the the Pacific BC area. No one supported the notion that on our boats the transducer that would shoot through the hull rather than a thu hull transducer would work well. I did an extensive...
- Mon Aug 22, 2022 11:04 am
- Forum: Engine / Transmission Forum
- Topic: Fluid Replacement Recommendations
- Replies: 8
- Views: 4481
Re: Fluid Replacement Recommendations
Hi Ken, 560ml is the amount I see recommended but I always find it a bit less than full. Too full = very bad. After all sorts of small manual extraction pumps I have settled (for now) on a large medical syringe. About 1" diameter and 6" long from most drug stores. These have enough frictio...
- Sun Aug 21, 2022 9:40 am
- Forum: Engine / Transmission Forum
- Topic: Fluid Replacement Recommendations
- Replies: 8
- Views: 4481
Re: Fluid Replacement Recommendations
I use the following: HD expert premium 50/50 engine coolant 6 quarts, Shell Rotella T5 SAE 15W-40 four quarts, Mobil Dexron -V1 ATF 560 - 580ml I change oil, filter and trans fluid every 100 hrs max and again at the end of the season. All three fuel filters one a year. 2000 engine / trans hours and ...
- Wed Aug 17, 2022 1:44 pm
- Forum: Hull, Prop, and Rudder Forum
- Topic: Prop + Net = *@#!!
- Replies: 2
- Views: 661
Re: Prop + Net = *@#!!
Sorry for the delayed response. The timing hole is adjacent the aft starboard engine mount. Slightly above the horizontal engine mount plate and in front of the mount bolt/nut. About a 3/4" hole +/-
Good info in both the Universal user and tech manual.
Good info in both the Universal user and tech manual.
- Sat Aug 13, 2022 1:05 pm
- Forum: Rigging Forum
- Topic: Rocna Anchror Question /Chain size
- Replies: 20
- Views: 8001
Re: Rocna Anchror Question /Chain size
Excellent discussion! I too changed out the old Bruce 33kg (1970s technology) for a Rocna 15. The rode is 120' 5/16 galvanized chain and 200' Samson 8 braid line. I run it on the starboard side as its longer and in pays out with no issue. I removed the spare smaller Bruce with 3/8 chain and rope rod...
- Mon Aug 08, 2022 11:40 am
- Forum: Hull, Prop, and Rudder Forum
- Topic: Prop + Net = *@#!!
- Replies: 2
- Views: 661
Prop + Net = *@#!!
Its happened to many and it happened to us last Friday am. Leaving our marina and motoring out the Vancouver Harbour we went through a very benign, somewhat unavoidable, little line of stuff in the water. Right away I was aware of a change in sound. Then a decrease of speed by perhaps 1.0 prop net.j...
- Mon Aug 08, 2022 11:04 am
- Forum: Engine / Transmission Forum
- Topic: Cutlass bearing replacement
- Replies: 7
- Views: 1402
Re: Cutlass bearing replacement
Hello schipp 790 I really appreciate your taking the time to make this post. Very clever. I'm assuming you replaced the shaft? It appears the wear on yours was at the bearing and very visible once the coupling end was released and the shaft drawn aft some. Might it have been an option to cut the sha...
- Thu Jun 23, 2022 2:46 pm
- Forum: Engine / Transmission Forum
- Topic: M35B Engine Overhaul?
- Replies: 3
- Views: 854
Re: M35B Engine Overhaul?
Thank you Brett ... as always, great advice.
- Thu Jun 23, 2022 11:26 am
- Forum: Engine / Transmission Forum
- Topic: M35B Engine Overhaul?
- Replies: 3
- Views: 854
M35B Engine Overhaul?
I'd really appreciate your opinions and experiences with whether or not to overhaul our M35B. We are approaching 2000 engine hrs. Its somewhat a product of living, boating in the Pacific Northwest. Winds are often unsuitable for getting where you're wanting to be so motoring and motor sailing happen...
- Wed Mar 30, 2022 12:13 pm
- Forum: Add-ons and Improvements
- Topic: Steering shaft info requested
- Replies: 5
- Views: 1100
Re: Steering shaft info requested
Confirmed - Tapered on our 2005 Mk1
We have the Lewmar folding wheel and love it.
We have the Lewmar folding wheel and love it.
- Sun Mar 27, 2022 4:55 pm
- Forum: Hull, Prop, and Rudder Forum
- Topic: Bottom Paint
- Replies: 2
- Views: 712
Re: Bottom Paint
Agreed, thanks Brett.
- Sun Mar 27, 2022 2:56 pm
- Forum: Hull, Prop, and Rudder Forum
- Topic: Bottom Paint
- Replies: 2
- Views: 712
Bottom Paint
I have searched all the posts on this topic but don't see much. I was hoping to start a discussion on this topic as to what you have found to work well for you both in bottom paint materials and application methods. Our boat (prior to us owning) has fallen victim to poor application processes and ya...
- Sun Mar 27, 2022 2:44 pm
- Forum: Engine / Transmission Forum
- Topic: Damper Plate
- Replies: 0
- Views: 1024
Damper Plate
Just a word of thanks to all who have gone before. The many previous posts were helpful. I attach an alternate engine lift set up. I was as surprised a 42" 2x4 will slip down each side of the engine and rest on the stingers (bit of mods) Its more for interest than any firm recommendation. I had...
- Sun Jan 09, 2022 1:10 pm
- Forum: Interior Forum
- Topic: FOR SALE: interior cabin carpet
- Replies: 4
- Views: 776
Re: FOR SALE: interior cabin carpet
Hello Monty
I attempted a private message but ???
Just inquiring if your carpets are still for sale.
Thank-you
I attempted a private message but ???
Just inquiring if your carpets are still for sale.
Thank-you